• Coleman Lazy Spa Error Code E04

Jacuzzi Whirlpool. OH = Overheat Protection (Heater is deactivated, pumps low speed is activated). COOL = Spa water is more than 20° F cooler than the temperature set point. FLO. = Flow Switch (heater is deactivated. Pump may also be deactivated). Hold = Panel sensors have been pressed too many times in a short period of time. HOT = Circuit Board temperature has exceeded acceptable limit.

Wondering what your spa is trying to tell you? Below is a list of common error codes from the top manufacturers of control equipment for hot tubs.Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa's equipment area. Pictured here is a Balboa® control system used in Belize Spas brand.Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice.

The E6 code is a warning that there is not sufficient water flow for the power pack to continue operating without possible damage. The power pack must shut down for self preservation. If you do not have enough water flow the area with the heating element will over heat and melt. 2019-6-19  Use our Flashing Lights solution.Select one flashing light as the problem, and then follow the steps in the solution. If these steps don't resolve the problem, you'll need to request a repair. Repair or warranty questions?

We make no representation as to the accuracy or completeness of this data and aren't responsible for errors or omissions. Refer to your owner's manual.Error & LCD Window Message Codes:ACC (Applied Computer Controls)CoLd = Temperature in the spa heater housing is below 40° F. Status of the heater element is unknown.

The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.OH = Over heat. The spa is at a temperature above 108°. Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected.

Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational.PSoC = Pressure switch open with circulating pump.PSoL = Pressure switch open with low pump.PSoH = Pressure switch open with high pump.ToE = Time out error. Rare system error. Spa unusable.

Contact ACC.Balboa(used by Belize Spas and many other hot tubs)pd = Power supply, unit running on battery backupOH = Sensors reading 112-118° F.OHH = Overheat. Spa has shut down. One sensor has detected 118° F at heater.OHS = Overheat. Spa has shut down.

One sensor has detected 110°F.Flo = Improper flow or pressure switch malfunctionCool = Water temp 20° below set pointICE = Potential freeze condition has been detectedSn1 = Hi-limit sensor malfunctionSn3 = Temp sensor malfunctionSnA = Spa is shut down. Sensor plugged into jack A is not working.Snb = Spa is shut down. Sensor plugged into jack B is not working.SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down.HFL = Substantial difference between temperature sensors detected.

Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of 'HFL' message with 24 hours). Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of 'dr' message).

Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike.(-) =Unknown water temperature.

. Remove any USB flash drives. Here's how:. Turn off your Xbox 360 console. Unplug any USB flash drives attached to your console. Cheat gta san andreas pc dan gta extreme indonesia. Turn on the console.If this step resolves the problem, reattach the USB flash drive to make sure that the error occurs only when the flash drive is connected.

Coleman Lazy Spa Error Code E04

If this is true, use another. Roll back the current software updates on your console, and then apply new ones. Here's how:. Press the Guide button on your controller. Go to Settings and select System Settings. Select Storage. Highlight (but do not select) Memory Unit.

On your controller, press the following buttons in order:. Left bumper. Right bumper. X buttonDon't know where these buttons are on your controller? See. Repeat step D.

When you see the following message, select Yes:Delete System UpdateIf any storage device contains a system update, the update and access to Xbox Live will be removed. To use these features again, sign in to Xbox Live and download the update. For more info, visit www.xbox.com/storage.Your console will restart after the operation is complete. Do you want to continue?YesNo. Your Xbox 360 console will restart. Original Xbox 360 console.